本吊掛式全自動浮法拉邊器(專利號：ZL200420052139.2、ZL200420052140.5、ZL200420077835.9)用于浮法平板玻璃生產，成對布置在錫槽兩側，沿錫槽內玻璃運行方向，以一定間隔設置多對組成拉邊器組。本機吊掛在設置于錫槽側面專用橫梁上，在錫槽側面兩立柱間可平行移動，調整布置位置；單臺五個自由度運動包含：拉邊輪無極調速旋轉；拉邊桿水平擺動；拉邊桿垂直升降運動；拉邊輪進出錫槽運動；拉邊輪下壓、抬起和緊急抬起。

     The suspended automatic top roller (Patent No.:ZL200420052139.2、ZL200420052140.5、ZL200420077835.9) is a necessary device for producing float glass. It is located at two side of tin bath in pairs and combined into the top roller units along running direction of glass ribbon in tin bath. It is hung on special crossbeam, which set at side of tin bath to move horizontally between two buckstay at side of tin bath, and adjust its position. Five freedom operations for single include: adjustable-speed rotation of top roller wheel; horizontal swinging of top roller bar; vertical elevating of top roller bar;top roller wheel getting into and out of tin bath; down-press, lifting and emergency of top roller wheel.

特點：Characteristic

 

◎ 拉邊桿與錫槽邊封用不銹鋼波紋管密封聯接；

◎ 拉邊桿冷卻水設置傳感器檢測水溫，超溫報警；

◎ 拉邊桿傳動齒型帶設置斷帶檢測報警傳感器，并使該對同時緊急抬起；

◎ 本機選用絕對值編碼器檢測，運動重復精度高，即使突然斷電，來電后記憶當前位置；

◎ 本機三種操作模式：手動操作、隨機控制箱操作、控制室遠程操作，其中遠程分上位機和面板操作；

拉邊器組使用：用總線組成網絡，遠程可對單臺、單對、多對分別或同時操作。

Edge sealing between top roller bar and tin bath is done by stainless steel corrugated pipe;

A sensor of cooling water of top roller bar is set for checking water temperature and alarming for overtem perature;

A alarm sensor for checking broken belt is set for drive tooth belt of top roller bar and emergency lifting at same time;

The absolute value coder inspection is selected for this device, repeat accuracy of movement is high, even if power is off, the current position will be memorize after power is on;

Three operation mode: manual operation, control box operation, remote operation in control room, in which, remote operation including computer and panel  operation;

Usage of top roller group: net is composed of the bus; remote  operation is used for single piece, one pair, and multi-pair separately or simultaneously.

主要性能及精度：Main performance and accuracy

 

拉邊輪  直徑：189mm或214mm   徑向跳動：≤0.2mm   

        線速度：60 ~960m/h 或54~1080m/h 

線速度波動： 1/10000

        線速度比：16或20                    

拉邊桿水平擺角：      工作范圍±16 °，極限±20°，精度0.1°

拉邊桿垂直升降行程：  100±0.2mm(工作標高時±50mm)

拉邊輪進出錫槽：      3700±0.2mm

Top roller wheel: Diameter:189mm or 214mm

                       Radial jigging: ≤0.2mm

                     Liner speed:60 ~960m/h or 54~1080 m/h

                     Fluctuation of linear speed:1/10000

                     Ratio of linear speed:16 or 20

Horizontal swinging angle of top roller bar: range of operation±16°， linit ±20°， accuracy0.1°

 

Vertical elevating stroke of top roller bar: 100±0.2mm( (working elevation: ±50mm)

Top roller wheel getting into and out of tin bath: 3700±0.2mm

 

主要用戶：Main users

     山西利虎玻璃（集團）有限公司Shanxi Lihu Glass (Group) Co., Ltd.

     安徽鳳陽玻璃有限公司Anhui Fengyang Glass Co., Ltd.

     成都南玻玻璃有限公司South Glass Group Ltd., Chengdu

     印尼TG-2浮法玻璃生產線Indonesia TG-2 float glass line

     南玻河北浮法玻璃有限公司Indonesia TG-2 float glass line

     信義環保特種玻璃（蕪湖）有限公司Xinyi Energy Saving Special Glass (Wuhu) Co., Ltd.